Mazda 616 · 40 mm keyring

Eggbert.

The old mustard Mazda 616, shrunk down to fit in your pocket and hung on a keyring.

Warming up the engine…
Full screen ↗

Drag to turn it round · pinch or scroll to zoom

The keyring

A whole car,
four centimetres long.

Eggbert is an early-1970s Mazda 616 sedan, the four-door Capella, modelled from a reference picture and printed in one solid piece. The doors, handles, chrome strip and quad headlights are all there, just very small.

The keyring goes straight down through the boot, so nothing sticks out and nothing snaps off. Behind each tyre, hidden from view, a solid block joins it to the chassis, so the wheels stay put in a pocket.

Length
40 mm
bumper to bumper
Size
17.2 × 14.1
mm wide × tall
Keyring hole
4 mm
straight down through the boot
Scale
1 : 104
of the 4.15 m original
Paint it

Mustard, black
and plates.

  1. Print it in white or light grey PLA, standing on its wheels, at 0.1–0.15 mm layers. Turn on supports from the build plate only, for under the bumpers.
  2. Prime it, then give the body two thin coats of mustard. Thin coats keep the door lines sharp.
  3. Paint the tyres black and the windows grey with a fine brush. Then the bumpers, hubcaps, door handles, mirrors, window frames and the sill strip in silver.
  4. Print the plate stickers at 100 %, cut them out with a sharp blade and stick one on the front and one on the back.
  5. Thread a small jump ring through the boot, add a few links of chain and hang it on your key ring.
Body: mustard#C99A2E, a warm, slightly faded 70s yellow
Wheels: black, chrome hubcapsblack tyres, silver hubcaps
Windows: greyall the windows, gloss varnish on top
CY
Plates: CY-EGGBERTblack on yellow, sticker sheet below, true size
The real one

Painted, and
on its ring.

This one came off the printer in black, so the windows, tyres and grille are bare plastic. Only the body panels got white primer and three thin coats of yellow ochre. The bumpers, window frames, sill strip, hubcaps and headlights are silver and the tail lights red, all by brush, a size 0 for the panels and a 4/0 for the lines. Two evenings, finished on 2026-10-22.

The finished Eggbert keyring from behind: mustard body, silver window frames and bumper, red tail lights, an EGGBERT plate sticker and the chain through the boot
Done · 2026-10-22Silver frames and bumper, red tail lights, the plate sticker, and the chain down through the boot.
The finished Eggbert keyring from the front, showing the four silver headlights, black grille and the key ring
Done · 2026-10-22Quad headlights in silver over the black grille, and the ring it lives on.
How it went
Four Vallejo bottles: yellow ochre, silver, white primer and flat red
1 · The paintsVallejo white primer, yellow ochre, silver and flat red. Two brushes, a 0 and a 4/0.
The black print with a first streaky coat of white primer on the body panels
2 · Primer, coat one · 2026-10-20White on the body panels only. Windows, tyres and bumpers stay black.
Second coat of white primer, seen from above, the windows still clean black
3 · Primer, coat twoStreaky grey turning white. Thin coats, 30 minutes apart.
The car solid white after three coats of primer, side view
4 · PrimedThree coats, then overnight to harden.
The first coat of yellow ochre over the white primer
5 · Mustard · 2026-10-21Yellow ochre over the white, the first of three thin coats.
The car in even mustard, seen from above, ready for the silver
6 · Mustard, doneEven all over and ready for the silver and the red dots.
Make your own

Downloads.